For Commercial ProfessionalsChange

Loading...

FOAMULAR® Insulation Product Selection Guide

* Refer to submittal sheet for each FOAMULAR® product for complete properties and application recommendations.

All Foamular XPS products are R-5 per inch of thickness except High-R CW Plus that is R-10 at 1-3/4", and R-12 at 2 1/8 " thick.

Click the ASTM C578 Type link to see all Foamular Extruded Polystyrene (XPS) products and properties, and a comparison to molded polystyrene (EPS).

Download the product selection guide (PDF 138KB)

Download the OSHA Hazard Communication Letter (PDF 23KB)

Construction
Application
FOAMULAR® Product* ASTM C578 Type Comments
General Purpose FOAMULAR® 150 X Slab edge, foundation, under light slab, steel stud sheathing, masonry cavity wall, concrete tilt-wall. For roofing applications, use THERMAPINK® XPS insulation.
FOAMULAR® 250 IV
Wall
Sheathing FOAMULAR® Insulating Sheathing X Laminated film on both sides for added strength.
FOAMULAR® PROPINK® X Reinforced laminated film on both sides for extra added strength.
Masonry Cavity Wall FOAMULAR® CW15 X 15 and 25 psi, 16" wide, fits between wall ties.
FOAMULAR® CW25 IV
FOAMULAR® High-R CW Plus IV 25 psi, 16" wide, fits between wall ties. Higher R per inch.
Furring FOAMULAR® INSULPINK® X Notched to accommodate 1 x 3 wood furring on inside surface of masonry or concrete walls.
FOAMULAR® INSULPINK® Z X Fits between Z-furring on inside surface of unit masonry or concrete walls.
Insulated Concrete Sandwich Panels FOAMULAR® 250 IV Used with low conductivity, metal or other composite grid type wall ties.
Exterior Insulation Finish System, EIFS FOAMULAR® 250 X Any PM class system such as the BASF Senergy Stucco CI Wall System.
Roof
Low Slope Commercial Roofing and Architectural Metal Roofing FOAMULAR® THERMAPINK® 18 X 18, 25 psi, used in a variety of roofing systems over a variety of deck types. Also available tapered to add slope to roof.
FOAMULAR® THERMAPINK® 25 IV
Recover Roofing FOAMULAR® DURAPINK® IV Used over existing membrane and under new mechanically attached single-ply.
PRMA, Plaza Deck, Waterproofing FOAMULAR® 404 VI Bottom side drainage channels on 4 edges for PRMA.
FOAMULAR® 604 VII
FOAMULAR® 404RB VI Bottom side drainage channels and top side ribbed surface for use under pavers in PRMA.
FOAMULAR® 604RB VII
FOAMULAR® 400 IV High load, vehicular traffic.
FOAMULAR® 600 VII
FOAMULAR® 1000 V
Under Slab
Load Bearing, High Strength, Under Industrial Slabs FOAMULAR® 400 VI 40, 60, 100 psi compressive strength. Engineer to match Foamular compressive needed to load on slab and slab design. Ranges from light pedestrian to heavy equipment and storage.
FOAMULAR® 600 VII
FOAMULAR® 1000 V
Under Slab, Low Temperature Storage FOAMULAR® LT30 IV 30 psi. Light to medium load.
FOAMULAR® LT40 N/A 40 psi. Heavier load.
Foundation
Below Grade Walls FOAMULAR® INSUL-DRAIN® IV Filtration fabric faced with drainage channels in foam
FOAMULAR® PINK-DRAIN™ IV Channel design prevents soil from clogging channels assuring long-term performance.
FOAMULAR® Fanfold DWB N/A Fanfold protection board for foundation waterproofing.
Agriculture
  FOAMULAR® AgTek IV Produced extra-long for roofing applications.
Specialty
  FOAMULAR® PINKCORE® X, IV, VI, VII Tight Tolerance board for Specialty and Engineering applications

To download product documentation, click on the icons above. Documents are in Adobe® PDF format.

Click here to download Adobe® Reader®. Construction details are in .DWG format.